kb.pub

📖 READER VIEW (Read-Only, Public Access)

Transmission Slipping: Difficulty Shifting

Публичная сессияСессия #30213.01.2026👁️ 67 просмотровНеисправности и диагностика транспортных средств
🤖

AI Analysis Summary

The automatic transmission is exhibiting slipping between gears, characterized by hesitation, high revving before engagement, and occasional difficulty shifting into gear. This indicates a significant internal transmission issue.

Описание проблемы

My automatic transmission seems to be slipping between gears. It feels like it's hesitating or revving high before engaging. Sometimes it's hard to get into gear.

Вопросы

5 вопросов
Q1

When did this problem start, and has it been getting progressively worse? (ID: 1635)

This problem started gradually about two months ago. At first, it was just a slight hesitation, almost unnoticeable. But over the last month, it's become much more pronounced. The slipping is more frequent, and the difficulty shifting into gear is definitely getting worse. It's making me nervous to drive it for any long distances.

Q2

Does the slipping occur in all gears, or only specific ones (e.g., only when shifting from 1st to 2nd)? (ID: 1636)

It seems to be happening in most gears, but it's most noticeable when I'm accelerating from a stop, so I'm assuming it's happening between 1st and 2nd. It also feels like it's struggling to downshift when I slow down, sometimes revving higher than it should before dropping a gear.

Q3

Have you noticed any unusual noises (grinding, whining) coming from the transmission? (ID: 1637)

Not really any grinding or whining, but there's definitely a noticeable 'thud' or 'clunk' when it hesitates to engage a gear, especially when shifting into reverse. It's not a smooth engagement anymore.

Q4

Have you checked the transmission fluid level and condition recently? If so, what did you observe? (ID: 1638)

I haven't personally checked it recently, but the last time I had it serviced about 6 months ago, the mechanic mentioned the transmission fluid was a bit low and looked a little dark. I haven't had it checked since then. I'm not sure how to check it myself, but I've been meaning to get it looked at.

Q5

Are there any warning lights illuminated on your dashboard, such as the check engine light or a transmission warning light? (ID: 1639)

Yes, the check engine light has been on for a few weeks now. I haven't noticed a specific transmission warning light, but the check engine light is definitely illuminated.

Выявленные причины

4 причины
#1

Низкий или загрязненный трансмиссионный флюид

80%

Недостаточная или ухудшенная трансмиссионная жидкость может привести к плохому смазыванию, перегреву и недостатку гидравлического давления, необходимого для правильного включения передач. Это распространенная и часто упускаемая из виду причина пробуксовки.

#2

Изношенные пакеты фрикционов или тормозные ленты

75%

Внутренние фрикционные пакеты или тормозные ленты в коробке передач отвечают за включение различных передач. Износ этих компонентов может привести к их неправильному сцеплению, вызывая проскальзывание и задержку включения.

#3

Неисправный гидротрансформатор

60%

Преобразователь крутящего момента передает мощность от двигателя к трансмиссии. Внутренние проблемы, такие как изношенные лопатки статора или утечки жидкости внутри преобразователя, могут вызывать проскальзывание и ощущение потери мощности.

#4

Проблемы с блоком управления трансмиссией (TCM) или соленоидами

50%

ТКМ управляет переключением передач на основе различных входных данных с датчиков. Неисправные соленоиды или неисправный ТКМ могут привести к неправильному гидравлическому давлению или времени переключения, вызывая проблемы с переключением и проскальзывание.

Рекомендуемые решения:

8 решений
💡

Scan for Diagnostic Trouble Codes (DTCs)

100%Official
Use an OBD-II scanner to check for any codes related to the transmission control system or solenoids.

🤖 AI Analysis

"The user has a check engine light on and is experiencing slipping and hesitation. Scanning for DTCs is the crucial first step to diagnose the underlying cause of these symptoms, as it will point towards specific systems or components that are malfunctioning."

💡

Check and Top Off Transmission Fluid

95%Official
Inspect the transmission fluid level and condition. If low, add the correct type of fluid. If the fluid is dark, burnt, or has debris, it needs to be flushed and replaced.

🤖 AI Analysis

"The user mentioned that the transmission fluid was low and dark during their last service. Low and degraded fluid is a very common cause of slipping and hesitation in automatic transmissions. Checking and topping off, or proceeding to a flush if necessary, is a highly relevant initial step."

💡

Transmission Fluid Flush and Filter Replacement

90%Official
A complete flush removes old, contaminated fluid and debris, while a new filter ensures proper fluid flow. This is often recommended if the fluid is in poor condition.

🤖 AI Analysis

"Given the user's report of low and dark transmission fluid, a transmission fluid flush and filter replacement is a very strong candidate for resolving or at least improving the slipping and hesitation. This addresses the potential issue of contaminated or insufficient fluid flow."

💡

Solenoid Replacement

85%Official
If specific solenoids are identified as faulty through diagnostics, they can be replaced individually.

🤖 AI Analysis

"Solenoids are critical for controlling fluid flow within the transmission and are often the cause of slipping and shifting issues. If DTCs point to solenoid problems, this is a direct and relevant repair. The 'thud' or 'clunk' when engaging gears could also be related to solenoid issues."

💡

TCM Reprogramming or Replacement

80%Official
The TCM may need to be reprogrammed to clear errors or replaced if it is determined to be faulty.

🤖 AI Analysis

"The Transmission Control Module (TCM) governs the transmission's operation. If it's malfunctioning or has corrupted software, it can lead to slipping and erratic shifting. Reprogramming or replacement is a relevant solution, especially if DTCs indicate TCM issues."

💡

Torque Converter Replacement

75%Official
The faulty torque converter needs to be removed and replaced with a new or remanufactured unit.

🤖 AI Analysis

"A faulty torque converter can cause slipping, hesitation, and a feeling of the engine revving higher than it should before engaging a gear. This aligns with the user's description of the problem, particularly the difficulty downshifting and the engine revving. It's a significant component that can cause these symptoms."

💡

Component Replacement

60%Official
In some cases, specific worn clutch packs or bands might be identifiable and replaceable without a full rebuild, though this is less common for widespread slipping.

🤖 AI Analysis

"While less common for widespread slipping, worn clutch packs or bands can definitely cause slipping between gears. If diagnostics can pinpoint specific worn components, this could be a more targeted repair than a full rebuild, but it's less likely to be the primary cause of widespread slipping without other indicators."

💡

Transmission Rebuild

50%Official
This involves disassembling the transmission to replace worn clutch packs, seals, bands, and other internal components.

🤖 AI Analysis

"A transmission rebuild is a comprehensive solution for internal transmission wear. While it would certainly address slipping, it's a major repair and usually considered when other, less invasive solutions have been ruled out or when the problem is severe and widespread internal damage is suspected. The user's symptoms, while concerning, might be resolvable with simpler fixes first."

Помочь другим